Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.
|Published (Last):||15 January 2015|
|PDF File Size:||19.73 Mb|
|ePub File Size:||1.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
For bending-resistant cable, see Attachment to Moving Parts on page C The lens, case, and fiber covering are made of plastic, so this setup cannot be used if there is a possibility of contact with solvents that will corrode or degrade e. Radiant noise Ingress of high-frequency electromagnetic waves directly into Sensor, from power line, etc.
Placing them in the same conduit or duct may cause damage or malfunction due to induction interference. Lock and unlock the fibers at an ambient temperature of?
Separate the noise source and the Sensor to a distance where noise does not affect operation.
Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch
Please know and observe all prohibitions of use applicable to the products. Be sure to read Safety Precautions on page 4.
Organic solvents will dissolve the surface. The Reflector cannot be mounted if there is any oil or dirt remaining. Typical measures are as given in the following table. To maintain the fiber characteristics, make sure that the lock is released before removing the fibers. Cable Bending Destruction Test Tough Wire Breaking Test With current flowing, bending is repeated to check the number of bends until the current stops.
The lens, however, is plastic. Precautions for Safe Use To ensure safety, always observe the following precautions. Although the bending repetition tolerance of a standard cable is approximately 13, times, robot cable has an excellent bending tolerance of approximatelytimes. Mutual Interference Mutual interference is a state where an output is unstable because the Sensors are affected by light from the adjacent Sensors.
As a general rule, wire the Sensor in a separate system, use an independent metal conduit, or use shielded cable. If not grounded, switching noise in the power supply may cause malfunction. Hold the connector cover to connect or disconnect the connector. Lens and Case The lens and case of the Photoelectric Sensor are primarily made of plastic.
Do not use thinner or other organic solvents. It is our practice to change model numbers when published ratings or features are changed, or when signi?
If the Sensor and the load are connected to separate power supplies, turn ON the Sensor power before turning ON the load power. Insert a capacitor, etc.
Keep organic solvents away from the Sensor. For the E3S-C, the optical axis and the mechanical axis are the same, so e3c-vx1g optical axis can be easily adjusted by aligning the mechanical axis.
Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output Buy from Cross
Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, use Sensors with the interference prevention function.
Separate Sensors to distance where interference does not occur. M8 and M12 Connectors? Values Given in Typical Examples The data and values given as typical examples are not ratings and performance and do not indicate specified performance. AC Two-wire Sensors Example: Typical examples include the minimum sensing object, engineering data, step height detection data, omrom selection list for specifications. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
When in doubt, special model numbers may be assigned to? Do not use it for such purposes. This catalog is protected by copyright and is intended solely for use in conjunction with the product. This information by itself is not suf? Ambient Conditions Do not use this Sensor in the following locations. Do not subject a shielded cable or coaxial cable to tension. Close mounting of Sensors is possible by alternating the Emitters with the Receivers in a zigzag fashion up to two Sensors.
Please notify us before copying or reproducing this catalog in any omrob, for any other purpose.
This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: However, if the workpieces are close to the Photoelectric Sensors, light from the adjacent Emitter may be received and cause the Sensor to change to the incident light state.
This is because the Sensors may affect each other and cause output chattering even if separated by more than the Sensor sensing distance.